pygame.camera
pygame module for camera use
pygame.camera.colorspace Surface colorspace conversion
pygame.camera.list_cameras returns a list of available cameras
pygame.camera.Camera load a camera

Pygame currently supports only Linux and v4l2 cameras.

EXPERIMENTAL!: This API may change or disappear in later pygame releases. If you use this, your code will very likely break with the next pygame release.

The Bayer to RGB function is based on:

Sonix SN9C101 based webcam basic I/F routines
Copyright (C) 2004 Takafumi Mizuno <taka-qce@ls-a.jp>
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
   notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
   notice, this list of conditions and the following disclaimer in the
   documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.

New in pygame 1.9.0.

pygame.camera.colorspace()
Surface colorspace conversion
colorspace(Surface, format, DestSurface = None) -> Surface

Allows for conversion from "RGB" to a destination colorspace of "HSV" or "YUV". The source and destination surfaces must be the same size and pixel depth. This is useful for computer vision on devices with limited processing power. Capture as small of an image as possible, transform.scale() it even smaller, and then convert the colorspace to YUV or HSV before doing any processing on it.

pygame.camera.list_cameras()
returns a list of available cameras
list_cameras() -> [cameras]

Checks the computer for available cameras and returns a list of strings of camera names, ready to be fed into pygame.camera.Cameraload a camera.

pygame.camera.Camera
load a camera
Camera(device, (width, height), format) -> Camera
pygame.camera.Camera.start opens, initializes, and starts capturing
pygame.camera.Camera.stop stops, uninitializes, and closes the camera
pygame.camera.Camera.get_controls gets current values of user controls
pygame.camera.Camera.set_controls changes camera settings if supported by the camera
pygame.camera.Camera.get_size returns the dimensions of the images being recorded
pygame.camera.Camera.query_image checks if a frame is ready
pygame.camera.Camera.get_image captures an image as a Surface
pygame.camera.Camera.get_raw returns an unmodified image as a string

Loads a v4l2 camera. The device is typically something like "/dev/video0". Default width and height are 640 by 480. Format is the desired colorspace of the output. This is useful for computer vision purposes. The default is RGB. The following are supported:

  • RGB - Red, Green, Blue
  • YUV - Luma, Blue Chrominance, Red Chrominance
  • HSV - Hue, Saturation, Value
start()
opens, initializes, and starts capturing
start() -> None

Opens the camera device, attempts to initialize it, and begins recording images to a buffer. The camera must be started before any of the below functions can be used.

stop()
stops, uninitializes, and closes the camera
stop() -> None

Stops recording, uninitializes the camera, and closes it. Once a camera is stopped, the below functions cannot be used until it is started again.

get_controls()
gets current values of user controls
get_controls() -> (hflip = bool, vflip = bool, brightness)

If the camera supports it, get_controls will return the current settings for horizontal and vertical image flip as bools and brightness as an int. If unsupported, it will return the default values of (0, 0, 0). Note that the return values here may be different than those returned by set_controls, though these are more likely to be correct.

set_controls()
changes camera settings if supported by the camera
set_controls(hflip = bool, vflip = bool, brightness) -> (hflip = bool, vflip = bool, brightness)

Allows you to change camera settings if the camera supports it. The return values will be the input values if the camera claims it succeeded or the values previously in use if not. Each argument is optional, and the desired one can be chosen by supplying the keyword, like hflip. Note that the actual settings being used by the camera may not be the same as those returned by set_controls.

get_size()
returns the dimensions of the images being recorded
get_size() -> (width, height)

Returns the current dimensions of the images being captured by the camera. This will return the actual size, which may be different than the one specified during initialization if the camera did not support that size.

query_image()
checks if a frame is ready
query_image() -> bool

If an image is ready to get, it returns true. Otherwise it returns false. Note that some webcams will always return False and will only queue a frame when called with a blocking function like get_image(). This is useful to separate the framerate of the game from that of the camera without having to use threading.

get_image()
captures an image as a Surface
get_image(Surface = None) -> Surface

Pulls an image off of the buffer as an RGB Surface. It can optionally reuse an existing Surface to save time. The bit-depth of the surface is either 24 bits or the same as the optionally supplied Surface.

get_raw()
returns an unmodified image as a string
get_raw() -> string

Gets an image from a camera as a string in the native pixelformat of the camera. Useful for integration with other libraries.




Edit on GitHub